[Design and Technology] Class Size year 10 wood

[Trevor Tippett]

Thanks Heather for the feedback on class numbers

Trevor

Sent from my iPad

> On 13 Aug 2016, at 8:13 PM, Aeschlimann, Heather j <Aeschlimann.Heather.j at edumail.vic.gov.au> wrote:
> 
> Hi Trevor,
> 
> I got our year 10 class capped at 22 for similar reasons and it was agreed to on the basis that a leisure PE program is capped at 20 and food tech at 20 so they agreed not to treat all electives the same if special considerations applied. Unfortunately my hard drive with ALL my documents on it died so I cant send you the request letter.
> 
> So it is okay for year 10 - but I have 25 in one year 12 class!
> 
> Heather
> From: destech-bounces at edulists.com.au [destech-bounces at edulists.com.au] on behalf of Trevor Tippett [tippettt at gmail.com]
> Sent: Saturday, 13 August 2016 1:03 PM
> To: destech at edulists.com.au
> Subject: [Design and Technology] Class Size year 10 wood
> 
> Hi folks!
> 
> I am the D & T wood teacher at Loyola college. I teach year 8, 9 & 10 wood.
> 
> My primary concern is the class size for year 10, this year it has been up to 27 students.
> 
> We make a small piece of furniture semester 1 and a coffee table semester 2. Managing larger products with a larger class size presents significant challenges. The areas in question comfortably accommodate 20 students making larger projects, not 27.
> 
> I have put together a proposal to the senior leadership team to reduce the class size to 20 students maximum. This has been based on occupational health & safety requirements, past student behavior, which has at times been extremely challenging, and the wood room layout.
> 
> The wood room is large enough to accommodate two year 8 class with 27 students, but we have a plant room that is linked to one side which substantially cuts the visibility to one side of the wood room. See diagram below.
> 
>  
> 
>  
> 
> Side a 27 students
> 
>  
> 
> Divider in the
> 
> middle of room
> 
>  
> 
>  
> 
>  
> 
> Plant Room
> 
>  
> 
> Side b 27 students
> 
>  
> 
>  
> 
>  
> 
> My proposal is to have the year 10 class, on the same side as the plant room (side b) because they pose the greatest challenging behavior’s and safety risk, whilst also making the larger products. This area can accommodate 20 students comfortably.
> 
> Could I please get some feedback on class sizes at other schools for senior years.
> 
> Any information my aid my proposal would be much appreciated.
> 
>  
> 
> Regards Trevor Tippett
> 
> IMPORTANT - This email and any attachments may be confidential. If received in error, please contact us and delete all copies. Before opening or using attachments check them for viruses and defects. Regardless of any loss, damage or consequence, whether caused by the negligence of the sender or not, resulting directly or indirectly from the use of any attached files our liability is limited to resupplying any affected attachments. Any representations or opinions expressed are those of the individual sender, and not necessarily those of the Department of Education and Training.
> _______________________________________________
> http://www.edulists.com.au - FAQ, resources, subscribe, unsubscribe
> Design and Technology Mailing List kindly supported by
> http://www.vcaa.vic.edu.au/vce/studies/designtech/destechindex.html  - Victorian Curriculum and Assessment Authority and
> DATTA Vic - Design and Technology Teachers' Association of Victoria
-------------- next part --------------
An HTML attachment was scrubbed...
URL: http://www.edulists.com.au/pipermail/destech/attachments/20160814/2675c537/attachment.html